AnyBook4Less.com | Order from a Major Online Bookstore |
![]() |
Home |  Store List |  FAQ |  Contact Us |   | ||
Ultimate Book Price Comparison Engine Save Your Time And Money |
![]() |
Title: Table Saw Techniques by Roger W. Cliffe, Bill Peters, Jim Schmitz ISBN: 0-8069-7912-7 Publisher: Sterling Pub. Date: December, 1984 Format: Paperback Volumes: 1 List Price(USD): $17.95 |
Average Customer Rating: 4.11 (9 reviews)
Rating: 2
Summary: Buyer beware...
Comment: I purchased this book and wish I had not. (Revised edition (c) 1997) It contains the most basic information which might be ok for a beginner but it is coupled with poor photographs and confusing (wrong?) information (i.e. The Taper Jig Text on pg 224 says "Measure back from hinge exactly 1-foot" yet the line illustration on Pg 222 clearly show's the 12inch measure from the Taper foot - the two directions are contradictory). The line drawings were helpful and pretty clear but as mentioned above I question their accuracy. I am not an expert and I did get a few bits of information from this book but nothing you could not find on the WWW.
Rating: 1
Summary: Not a "good" book
Comment: Sorry, but I disagree with all the "good" reviews here. I made the mistake of reading them, then ordering the book. It is not worth the money, nor the time it takes to look at it.
The pictures all look like they are from a 1940's high school shop manual. Pictures lack detail and are blurry.
Descriptions of accessories are lacking in detail and don't seem to note "how to make" any of them.
My suggestion is to look elsewhere for "table saw techniques" rather than buy this book.
Sorry I didn't do so.
Rating: 5
Summary: One of two excellent starter books for info on tablesaw use
Comment: I am just starting out in the world of being a hobbiest woodworker and I wanted books on the tablesaw to give information on proper setup, use, maintenance, and safety techniques (better to learn to keep your fingers right from the start). After reading the other (above) reviews of this book, I purchased it. It turns out to be a wonderful source of information for the beginner. I team this book with "Woodworking - The Right Technique" by Bob Moran as two volumes a beginner should have (and read thoroughly) before embarking on using your tablesaw. Everytime I re-read either of these volumes, I pick up something new that I didn't pay attention to the first time.
This book (along with the the Moran book) are highly recommended.
![]() |
Title: Woodworking With the Router: Professional Router Techniques and Jigs Any Woodworker Can Use by Bill Hylton, Fred Matlack ISBN: 0762102276 Publisher: Readers Digest Pub. Date: December, 1998 List Price(USD): $19.95 |
![]() |
Title: The Table Saw Book by Kelly Mehler ISBN: 1561584266 Publisher: Taunton Press Pub. Date: January, 2003 List Price(USD): $19.95 |
![]() |
Title: Woodworking: The Right Technique: Three Practical Ways to Do Every Job-And How to Choose the One That's Right for You by Bob Moran, Nick Engler ISBN: 0762102284 Publisher: Readers Digest Pub. Date: January, 1999 List Price(USD): $27.95 |
![]() |
Title: The Table Saw Book by Richard J. de Cristoforo ISBN: 0830627898 Publisher: McGraw-Hill Professional Pub. Date: 01 December, 1987 List Price(USD): $24.95 |
![]() |
Title: Building Cabinet Doors & Drawers by Danny Proulx ISBN: 0941936562 Publisher: Linden Publishing Pub. Date: May, 2000 List Price(USD): $21.95 |
Thank you for visiting www.AnyBook4Less.com and enjoy your savings!
Copyright� 2001-2021 Send your comments